How To Repair A Rod

Download Article

Download Article

Modern fishing rods don't break hands, but they can exist fixed easily with a few elementary tools you may have at home. If your rod snapped, you can mend information technology together with a fiberglass pole and epoxy to hide the break. When one of the guides breaks, you tin can remove it and wrap a new one in its place. Yous can change rod tips if they snap or break every bit well. With a little bit of work, yous can set your rod so it's as good every bit new!

1. 1

   Sand or cutting the broken ends of the rod so they're flush. Employ 180- or 220-grit sandpaper to smooth the ends then they fit together easily if the rod has a clean break. If your fishing rod has a jagged border, then use a pair of scissors to cut the abrupt edges off of the end of the rod then the pieces are flush. Later you make your cut, use sandpaper to smoothen out the edges and roughen upwardly the surface.^[1]

   • Jagged edges are weaker and are more likely to break again than edges that are flush with i another.

2. 2

   Measure the circumference of the rod. Use a flexible record measure and wrap it around the cleaved stop of your fishing rod. And so measure the circumference on the other piece of your fishing rod to see if it's skinnier. Write downward your measurements so you know what pole size you need for fixing your rod.^[2]

   • You lot can also measure the diameter of the rod on both of the broken ends if you don't have a flexible measuring tape.

   Advertising

3. 3

   Cut a piece of fiberglass pole so information technology's almost 12 in (30 cm) long. Get a fiberglass pole that has a circumference that's about ¹⁄_viii – ^ane⁄_iv inch (0.32–0.64 cm) smaller than your line-fishing rod. Use a hacksaw to cut out a 12 in (30 cm) section of the pole so information technology tin fit within your fishing rod and support the rod without breaking.^[three]

   • You can buy fiberglass poles from your local hardware store. Information technology doesn't affair what color you use since it volition fit inside of the rod.
   • If your line-fishing rod isn't hollow, then using a fiberglass pole won't work. Y'all tin either endeavour to tape your rod back together or become a new i.

   Tip: You tin can also cutting a section off of an old fishing pole that you don't use anymore if you lot don't have a fiberglass rod.

4. 4

   Slide the fiberglass pole into one side of the fishing rod. Hold your rod horizontally so you tin can position the fiberglass pole in the rod without information technology sliding too far. Button one stop of the fiberglass pole into the finish of the rod with the handle. Keep sliding the pole into the line-fishing rod until there'due south half-dozen inches (15 cm) sticking out from the stop.^[4]

   • If the pole doesn't fit snugly inside the fishing rod, then wrap the pole with duct or masking tape to make it thicker.

5. 5

   Apply 2-office epoxy to the exposed side of the fiberglass pole. Open up your two-function epoxy and pour it into a bowl. Use a paintbrush to spread a thin layer of the epoxy on the exposed end of the fiberglass pole. In one case the 2-role epoxy is mixed, piece of work speedily so it doesn't dry or fix before you put your rod back together.^[v]

   • You tin can buy two-part epoxy from any hardware or arts and crafts store.

6. 6

   Slide the other office of the rod onto the fiberglass and permit it dry out. Slowly button the other end of your rod onto the exposed end of the fiberglass pole. Make certain the guides on the pole line up with one another and so your line doesn't get tangled when you try using your pole again. Push the ii pieces of the rod together then they're flush. Permit the epoxy prepare overnight and so it firmly adheres to the rod.^[half-dozen]

   • The epoxy doesn't set right away, and then you can still rotate or movement the rod pieces once y'all slide them together.
   • If whatsoever epoxy comes out of the joint while y'all're sliding the pieces together, wet your finger and smooth out the epoxy so it isn't as visible.
   • Wrap a layer of electric tape around the seam if you want an boosted layer of security.

Advertizement

1. 1

   Cut the tape or thread around the broken guide with a razor bract. Apply a straight razor bract or a craft knife to remove any threading that may be surrounding the rod guide. If information technology'due south hard to remove using simply a blade, then try heating the area for 3-four seconds with a lighter to loosen whatsoever of the adhesives. Peel off the tape and unwind the threading until the old, cleaved guide comes off of the rod.^[seven]

   • Rod guides are the circular metal pieces forth the length of the rod that help go along your line directly.
   • Be careful not to estrus the rod for too long since it could crusade harm to it.
   • Don't cut into the rod with your razor, or else you could damage it and get in weaker.

2. 2

   Sand the rod and foot of the new guide to get better adhesion. Apply 120- or 220-dust sandpaper to get rid of any leftover adhesive and to add tooth to the rod. Rub all the way effectually the rod on the spot where you desire to place the new guide. Then, employ your sandpaper on the human foot of the guide, which is the apartment role that rests against the fishing rod.^[8]

   • You tin can buy new fishing guides at sporting good stores. Brand sure the new guide is the same size and style as the other guides on your fishing rod or else your line may snag or get tangled.

3. iii

   Tape the new guide onto the rod and then it's aligned. Press the foot of the new guide onto the rod so it's in line with the other guides. Rip off a thin piece of masking tape and wrap it around the human foot and then information technology'due south held in identify. That style, you lot don't need to keep property it in place while you wrap it.^[9]

   • Yous tin can also use super glue, only information technology volition be difficult to motility or readjust once the glue is set.

4. 4

   Wrap the foot of the guide with thread to hold it in place. Any type of thread will work for wrapping your guide onto the rod. Loop your threading around the rod and so information technology'south ^ane⁄₂ – ⁱⁱⁱ⁄₄ inch (1.3–1.9 cm) from the guide's foot on the side closest to the handle. Maintain tension on the loop and offset tightly winding the thread around the rod. Make sure the thread doesn't overlap with loops you lot've already made and that they are affluent with one another.^[10]

   • Have the slice of record off of the pes y'all've wrapped everything below it.

   Tip: Use a thread that matches the color of your rod if you lot want information technology to alloy in.

5. 5

   Place a looped slice of thread over the wrap when in that location'south ¹⁄₈  in (0.32 cm) left. When your wrapping is ¹⁄₈ inch (0.32 cm) from the round office of the guide, stop winding the thread around the pole. Cut a separate piece of thread and so it'southward virtually half-dozen inches (xv cm) long and fold it in half to class a loop. Lay the 2d piece of thread on summit of your wrapping then the loop sticks out nearly your guide.^[11]

   • If y'all don't have whatever other thread, yous can also use a thin line-fishing line instead.

6. vi

   Wrap the final ¹⁄₈  in (0.32 cm) over the 2nd piece of thread. Once the looped slice of thread is on acme of the wrapping, keep spinning your thread effectually the foot of the guide. Go along wrapping the final ⁱ⁄₈ inch (0.32 cm) of the guide so the middle of the looped piece is held against the rod.^[12]

7. 7

   Feed the thread through the looped piece and pull information technology tight. Once y'all attain the stop of your wrapping, cut the end of the thread yous used to wrap and pull it through the centre of the loop. Pull the other end of the looped slice down and away from the guide to pull the thread underneath the wrapping. This fashion, the wrapping is secured to the rod without having to tie a knot.^[xiii]

   • If you don't want to use a looped piece of thread, you lot can also try tying a knot in the threading, but it may not be every bit strong and it could be more difficult.

8. 8

   Paint 2-part epoxy onto the thread and let it dry out. Mix the 2 parts of the epoxy in a small dish with a paintbrush until they are thoroughly combined. Paint a thin layer of the epoxy over your threading so information technology hardens and stays in place. Keep the rod horizontal and allow information technology dry overnight before yous endeavor using your rod once more.^[14]

   • Work quickly with the epoxy since it volition quickly offset to dry out and harden one time you mix it.

Advertisement

1. 1

   Heat the tip peak of your fishing rod with a lighter to loosen the agglutinative. Set up the rod horizontal so yous can easily reach the tip. Hold a lighter underneath the tip pinnacle of the rod, which is the ringed piece at the terminate of the rod, and heat it upwards for 4-five seconds at a time. Once it'due south heated, effort pulling it off with a pair of pliers or by hand. If information technology doesn't come off easily, try heating information technology for some other few seconds.^[15]

   • Heating the tip elevation helps loosen the adhesive holding information technology in identify and then it'south easier to remove.
   • If the tip snapped off of your rod, then you can remove the former tip top from the broken slice or you can skip this step.

2. 2

   Smooth the tip of the rod with sandpaper to remove any shards. Rub the exposed tip of the rod with 120- or 220-grit sandpaper to smooth it out. Rotate the rod around the sandpaper until the tip is shine and affluent. It's okay if there are modest abrasion marks on the rod tip since it will take better adhesion to the new tip top.^[16]

   Tip: If sandpaper isn't plenty to remove the shards on the end of your fishing rod, then carefully cut off the ends with a scissors.

3. 3

   Cut pieces of rod cement into strips that fit inside your new tip elevation. Rod cement is an adhesive that comes in a solid block and is used for fishing rods to concur guides and tips in identify. Use a razor or craft knife to cut out small strips of the rod cement so they fit inside the hollow chamber on your rod tip peak.^[17]

   • Y'all tin buy rod cement and new tip tops from your local sporting goods store or online.

4. 4

   Melt the rod cement inside the tip top with your lighter. Hold the new tip acme with a pair of pliers and put the pieces of rod cement in the hollow tube at the end of it. Employ your lighter to oestrus the rod cement for four-5 seconds and melt it so you lot can adhere it to your rod. Once the rod cement is melted, piece of work quickly and so it doesn't solidify again.^[xviii]

5. 5

   Slide the tip top onto your rod so it lines up with the guides and let it dry out. While the cement is still hot, slide information technology onto the tip of your rod and rotate it so the ring is in line with the other guides. Wipe away whatever excess rod cement with a piece of paper towel and let information technology set up for at least 1-2 hours. One time the cement is dry out, your rod is set to use!^[19]

   • If y'all demand to adjust or reposition the tip acme later on the cement is dry out, then rut information technology over again for 3-4 seconds with your lighter.

Advertisement

Add New Question

• Question

  Where do I buy epoxy resin mucilage?

  

  At whatsoever home improvement or hardware shop.

Inquire a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Advertisement

• Take your rod to a fishing supply store or a repair person if you accept trouble fixing it on your own.

• If you need to fix a snapped rod in an emergency, overlap the pieces past vi inches (15 cm) and tape them together tightly.^[20]

Thanks for submitting a tip for review!

Advert

• Don't hold a flame against your rod longer than a few seconds or else you could permanently damage the rod.

• Be careful while working with razor blades so you don't accidentally cutting yourself.

Advertisement

Things You'll Need

• Scissors
• Sandpaper
• Tape measure
• Fiberglass pole
• Hacksaw
• ii-part epoxy
• Bowl
• Paintbrush
• Electric tape (optional)

• Razor blade
• Lighter
• Sandpaper
• Masking record
• Rod guides
• Thread
• 2-office epoxy
• Dish
• Paintbrush

• Lighter
• Pliers
• Sandpaper
• Rod cement
• Craft knife
• Rod tip top

Nigh This Commodity

Article Summary Ten

To gear up a snapped angling rod, try using a fiberglass pole and some epoxy. First, sand the snapped edges to make them affluent. Smooth edges are stronger and less likely to interruption. Cutting a 12 inch long piece of fiberglass pole using a hacksaw. Slide one end of the pole into your fishing rod until at that place are 6 inches sticking out. Once the fiberglass pole fits snugly into the rod, apply epoxy to the exposed end using a paintbrush. Connect the second one-half of the cleaved rod to the fiberglass pole and let the epoxy set. To replace the rod guide, offset, remove whatever threading from effectually the guide using a craft knife. Marshal the new guide onto the rod and use record to agree it in place. Wrap the new thread over the guide and then cover it in epoxy to set it. For more ideas on fixing a broken fishing rod, like how to alter a rod tip, read on.

Did this summary help you?

Cheers to all authors for creating a page that has been read 214,599 times.

Did this article assist you?

Source: https://www.wikihow.com/Fix-a-Broken-Fishing-Rod

Share this post